As an experienced supplier of Excavator Hydraulic products, I've encountered numerous inquiries regarding the issue of low hydraulic pressure in excavators. This problem can significantly impact the performance and efficiency of an excavator, leading to reduced productivity and potential safety hazards. In this blog post, I'll delve into the various reasons behind low hydraulic pressure in excavators, providing insights and solutions to help you address this common issue.
1. Fluid - Related Issues
Contaminated Hydraulic Fluid
Hydraulic fluid plays a crucial role in the proper functioning of an excavator's hydraulic system. Over time, the fluid can become contaminated with dirt, debris, metal particles, and moisture. Contaminants can cause abrasion to the internal components of the hydraulic system, such as pumps, valves, and cylinders. For example, dirt particles can scratch the smooth surfaces of the cylinders, leading to leaks and a decrease in pressure.
Regularly checking the hydraulic fluid's condition is essential. You can use a fluid analysis kit to determine the level of contamination. If the fluid is contaminated, it should be drained and replaced, and the hydraulic filter should also be changed.
Incorrect Fluid Viscosity
The viscosity of the hydraulic fluid is another important factor. If the fluid is too thin, it may not provide adequate lubrication and sealing, resulting in internal leakage and reduced pressure. On the other hand, if the fluid is too thick, it can impede the flow of the fluid, causing the pump to work harder and potentially leading to pressure drops.
It's important to use the hydraulic fluid recommended by the excavator manufacturer. The viscosity of the fluid should be suitable for the operating temperature range of the excavator.
Low Fluid Level
A low hydraulic fluid level is a common cause of low pressure. If there is not enough fluid in the system, the pump may not be able to draw in an adequate amount of fluid, resulting in cavitation and reduced pressure. Cavitation occurs when the pressure in the fluid drops below its vapor pressure, causing the formation of vapor bubbles. When these bubbles collapse, they can damage the pump and other components.
Regularly check the fluid level in the hydraulic reservoir and top it up if necessary. Inspect the system for any signs of leakage, as this could be the reason for the low fluid level.
2. Pump - Related Issues
Pump Wear and Tear
The hydraulic pump is the heart of the excavator's hydraulic system, responsible for generating the pressure needed to operate the various components. Over time, the pump can experience wear and tear due to continuous use. The internal components of the pump, such as the gears, vanes, or pistons, can become worn, leading to a decrease in pump efficiency and pressure.
A sign of a worn - out pump is a decrease in the excavator's lifting capacity or slow operation of the hydraulic functions. If the pump is worn, it may need to be repaired or replaced.
Pump Cavitation
As mentioned earlier, cavitation can occur in the pump if the fluid level is low or if there are air leaks in the suction line. Cavitation not only reduces the pressure but also causes damage to the pump's components. The pump may make a noisy rattling or knocking sound when cavitation occurs.
To prevent pump cavitation, ensure that the hydraulic fluid level is correct and that there are no air leaks in the suction line. Check the connections and seals for any signs of damage.


3. Valve - Related Issues
Defective Pressure Relief Valve
The pressure relief valve is designed to protect the hydraulic system from over - pressure. If the pressure relief valve is defective, it may open prematurely, allowing the hydraulic fluid to bypass the system and return to the reservoir. This can result in low hydraulic pressure.
A faulty pressure relief valve may also have a stuck spool or a damaged spring. To diagnose a defective pressure relief valve, you can use a pressure gauge to measure the pressure at different points in the system. If the pressure is lower than expected, the pressure relief valve may need to be inspected and replaced. You can refer to our Overcenter Valve VBCD - G12 - DE for high - quality replacement options.
Malfunctioning Control Valves
Control valves are used to direct the flow of hydraulic fluid to the various components of the excavator, such as the boom, arm, and bucket. If a control valve is malfunctioning, it may not be able to regulate the flow of fluid properly, leading to low pressure.
A control valve may have a stuck spool or a damaged seal. This can cause the fluid to leak internally or prevent the proper flow of fluid to the desired component. To address this issue, the control valve may need to be disassembled, cleaned, and repaired. In some cases, it may need to be replaced. Our Hydraulic Flow Divider Directional Control Valve can be a reliable solution for replacing malfunctioning control valves.
4. Cylinder - Related Issues
Leaking Cylinders
Hydraulic cylinders are used to provide the linear motion required for the operation of the excavator's boom, arm, and bucket. If a cylinder is leaking, it can cause a loss of pressure in the system. Leaks can occur due to damaged seals, worn piston rods, or cracked cylinder barrels.
Inspect the cylinders for any signs of oil leakage, such as wet spots or oil stains. If a leak is detected, the damaged seal should be replaced. In more severe cases, the cylinder may need to be rebuilt or replaced. We offer a wide range of Hydraulic Components Hydraulic Ram Cylinder Parts for cylinder repair and replacement.
Cylinder Binding
Cylinder binding can also cause low hydraulic pressure. This can happen if the cylinder is misaligned, the piston rod is bent, or there is debris in the cylinder. When the cylinder binds, the pump has to work harder to overcome the resistance, which can lead to pressure drops.
To address cylinder binding, the cause of the binding needs to be identified and corrected. This may involve realigning the cylinder, straightening the piston rod, or cleaning the cylinder.
5. Other Factors
Air in the Hydraulic System
Air can enter the hydraulic system through leaks in the suction line, loose connections, or improper filling. Air in the system can compress and expand, causing fluctuations in pressure and reducing the overall efficiency of the system.
To remove air from the hydraulic system, you can use a bleeding procedure. This involves opening the bleed valves at the highest points in the system to allow the air to escape.
System Overheating
Overheating of the hydraulic system can cause the hydraulic fluid to break down, reducing its viscosity and lubricating properties. This can lead to increased internal leakage and low pressure. Overheating can be caused by factors such as a clogged radiator, a malfunctioning cooling fan, or continuous operation under heavy loads.
To prevent system overheating, ensure that the cooling system is working properly. Clean the radiator regularly and check the cooling fan for any signs of damage.
In conclusion, low hydraulic pressure in an excavator can be caused by a variety of factors, including fluid - related issues, pump problems, valve malfunctions, cylinder issues, and other factors such as air in the system and overheating. By understanding these causes and taking appropriate preventive and corrective measures, you can ensure the proper functioning of your excavator's hydraulic system.
If you are experiencing low hydraulic pressure in your excavator or need high - quality hydraulic components for repair or replacement, don't hesitate to contact us. We are dedicated to providing you with the best solutions and products for your excavator's hydraulic system. Our team of experts is ready to assist you with any inquiries and help you make the right purchasing decisions.
References
- "Hydraulic Systems Handbook" by Rexroth Hydraulics
- "Excavator Maintenance and Repair Guide" by Caterpillar Inc.




